Welcome to another Crafty Wednesday!
Sorry I haven’t posted too much else over the past week. Where does the time go? It has been busier than usual and I didn’t even have an interview to post last weekend. I had been toying with doing another character interview, but didn’t have time to compile one.
Okay, enough chit-chat. On with the cards! This card is the last one I made for the Sketch Challenges at my October scrapbook weekend. It is a landscape-oriented card, which called for two round-cornered squares on each side in different patterned paper, a fancy label section in the middle with a sentiment and a main element in the centre of the card. In addition, there should be embellishments along the top of the left-hand square and the bottom of the right-hand square.
Now let’s see my interpretation of the Sketch Challenge:
As you can see, I decided not to go with a ‘Partridge-In-A-Pear-Tree’ element but chose instead a poinsettia. You can get these types of flowers from your local craft store. There are four layers to mine – a paper flower, a fine mesh flower shape overlay and two paper leaf shapes held together with a yellow brad. Instead of centering the poinsettia, I decided to off-set it a bit, piercing the edge of the left-hand square before attaching it to the card.
I ran the front of the card base through the Cuttlebug, using the ‘Victoria’ embossing folder before attaching the squares. The label was cut and embossed with the Cuttlebug as well, using the ‘Fanciful Labels’ folder. I used a sponge to brush on a pale green ink to the raised parts of the label and heat-embossed the sentiment (from Close To My Heart‘s ‘Card Chatter – Christmas’ clear acrylic stamp set) with black embossing powder. I just realized I didn’t add the embellishments. I might still do so as I picked up some pearlized self-sticking ‘jewels’ that I could add along the edges of the squares to ‘punch’ it up a bit.
The design was very simple, so I finished the inside of the card in similar style by simply cutting out the label (Sizzix ‘Decorative Labels #4’) and embossing the sentiment across its middle.
The design on the next card was one that came to me in a dream. (Yes, I really do dream about making cards!) I thought it would look like a snow globe. What do you think?
White card stock base (8-1/2″ x 5-1/2″, folded in half).
Red/orange patterned paper as the background (5-1/2″ x 4-1/4″)
Dark green card stock (4-1/4″ x 3″).
2″ circle of white card stock (cut with a circle punch)
Reindeer stamp (I used the one from Stampin’ Up‘s ‘Winter Post’ wood stamp set).
2 – 2″ circles cut from a Sookwang sheet
Dark green ink pad (or black)
Tree stamp (I used the one from Stampin’ Up‘s ‘Christmas Lodge’ set)
Close To My Heart‘s ‘Vanilla Cream’ pigment-based ink pad (or something similar that won’t bleed into the card stock)
6-1/2″ length of 1/4″ wide white ribbon tied in a bow
4-1/2″ x 3/4″ scrap of white card stock
Versa Mark sticky pad (or Martha Stewart‘s ‘Glue Pad’)
Black embossing powder
1/4″ wide Sookwang double-sided tape
1. Use Sookwang tape to attach red/orange paper to front of the card base
2. To the right-hand side of the green card stock rectangle, stamp the tree using the Vanilla pigment ink pad. NB: Make sure you have scrap paper underneath the project so ink will not transfer to your desk top, since you will only be stamping half the tree. Set aside to allow drying time as the pigment ink takes much longer than normal inks to dry.
3. Stamp reindeer onto white card stock circle.
4. Affix Sookwang circles to both front and back of reindeer circle, but keep the backing on the rear until glitter has been applied.
5. Peel front backing off Sookwang/reindeer circle. Sprinkle on the glitter, rubbing it all around the circle until no sticky parts remain. Shake off extra glitter.
6. Once the tree on the green card stock has completely dried, peel off remaining Sookwang backing and affix sparkly reindeer circle to the centre of green card stock.
7. Using Sticky Dots, attach ribbon bow to the top left-hand corner of the green rectangle, securing the ends to the back of the card stock.
8. Attach green card stock to centre of red/orange patterned paper using Sookwang tape.
9. Stamp the sentiment onto scrap of white card stock using Versa Mark. Sprinkle embossing powder over it, ensuring that all the sentiment has been covered. Use heat tool to set the powder. Once the powder has cooled, cut around sentiment.
10. Affix sentiment to bottom of green card stock and overlapping the red/orange pattern slightly
And you’re done! It always seems more complicated when I write it all out in point form, like this. It really isn’t all that difficult. The main thing you need to remember is how long the pigment ink takes to dry. I’ve often ruined cards because I didn’t wait long enough and the image got smudged.
This final card is very cute, I think. I want to thank my sister-in-law for lending me her stamp. It went very well with the candy cane patterned paper I found.
I stamped the image using a Versa Mark sticky pad and sprinkled the black embossing powder over it, shaking off the extra. I used my heat tool to set the powder, then painted the candy cane, the light chord and the light bulbs with my shiny paints. Using the cotton balls that come with the set, I smudged ‘Pebbles Cream Chalk’ to make the ‘glow’ around the light bulbs and add colour to the mouse. Using my paper cutter, I cut out around the mouse and rounded the corners with a paper punch. I cut out a rectangle of wine-coloured card stock that was about a 1/2 inch larger than the mouse, also punching the rounded corners. I then rubbed the edges with a Versa Mark pen, sprinkled peppermint-scented embossing powder onto the sticky surface and used my heat tool to set it. It became a bit shiny, as you can see, and added that extra ‘Scratch-and-Sniff’ element that goes so well with the candy cane theme.
I attached the mouse to the red card stock and the red card stock to the candy cane patterned paper with a glue runner. I affixed the entire card front to a plain white card stock base (5-1/2″ x 8-1/2″, folded in half) with Sookwang two-sided tape to hold it securely.
There’s only one more card that I made during my crafting weekend, but it involves a brand new product and process which I will show you next time.
In the meantime, happy crafting, everyone! 🙂